Made to measure shutters are only as good as the survey behind them. A panel built perfectly to the wrong size is still the wrong size, and a large share of remakes can be traced back to something missed or misread on the day of the survey.
This checklist is for retailers, surveyors and installers who measure for bespoke shutters. It covers how to choose between inside and outside fitting, which measurements to take, the obstructions that catch people out and what to record on the order so the factory builds exactly what you intended.
Start by deciding how the shutter will be fitted
Before a tape measure comes out, decide whether the shutter will sit inside the window recess or on the wall around it. Every later measurement depends on that choice, so make it first and write it at the top of the survey sheet.
An inside or reveal fit sits within the recess and gives the neatest finish. It needs enough depth for the frame and for the louvres to tilt without hitting the glass or the handles. An outside or face fit is fixed to the wall or architrave around the window, which is useful when the recess is too shallow, badly out of square or interrupted by tiles and sills.
Some windows suit either method, and the customer may have a preference once you explain the difference in appearance. The range of shutter styles you offer also affects the decision: a full height shutter on a bay may need a different approach to a café style panel on a kitchen window.
Your choice of frame type works hand-in-hand with the fitting method. For reveal fits, an L-frame is commonly used when sitting directly on the window casing or jamb, whereas a Z-frame offers a decorative lip that wraps around the edges of the recess to hide small gaps or minor out-of-square casing. For outside face fits, an L-frame fixed directly to the wall or architrave provides the required support and clean finish. Identifying the right frame profile early ensures that you record accurate clearance dimensions and select the correct hardware options for the order.
The measurements every survey needs
A good survey gives the factory everything it needs without a follow-up phone call. Take each measurement at least three times and in more than one place, because very few UK windows are perfectly square, especially in older houses.
Width and height
For a reveal fit, measure the width at the top, middle and bottom of the recess and record all three. Do the same for the height on the left, centre and right. The smallest figure is usually the one that matters, but the spread between the readings tells the factory how far out of square the opening is.
For a face fit, measure the area you want the frame to cover, including any overlap onto the wall. Agree the overlap with the customer, as it affects how much light leaks around the edges when the louvres are closed.
Depth and clearance
Measure the depth of the recess from the face of the wall back to the window frame, at several points. Then check the louvre clearance: when the louvres tilt, they swing out towards the glass, and larger louvres need more space. If there is not enough depth, the louvres will catch on handles or the window itself. Check which louvre sizes are available in the Slim Line composite range before you promise the customer a particular look.
Record any sloping sills or tiled reveals at this stage. A sill that drops away towards the room can leave a visible gap under a reveal-fitted frame unless it is planned for.
Diagonals
Measuring both diagonals of the recess is the quickest way to spot an out-of-square window. If the two diagonals differ by more than a few millimetres, note it clearly. The factory and the fitter can then decide whether a frame with more tolerance, a face fit or a little packing on site is the better solution.
Obstructions that cause most remakes
Most survey errors are not about the tape measure. They come from things in or around the window that were not recorded and only show up on fitting day.
Walk around each window and look for anything that could stop the frame sitting flat or the panels opening fully. These are the items that cause the most trouble:
- Window handles and locks that project into the recess, particularly on uPVC and tilt and turn windows
- Trickle vents on the top of the frame, which can block a reveal-fitted top rail
- Radiators, sockets and switches directly below or beside the window
- Curtain poles, blind brackets and pelmets that the customer plans to keep
- Sills that project beyond the wall and stop a face-fitted frame reaching the floor or wall line
- Plaster that has been dressed into the reveal at an angle rather than square
For each obstruction, note the size and position and measure how far it projects. A handle that projects 40mm into a recess means something very different to one that projects 15mm. If you are unsure whether a fitting detail can be handled in production, check before the order goes in rather than after. Fitters who are newer to composite products will also find useful background in this article on installing composite shutters .
Taking a photograph of each window from straight on and from each side adds almost no time to the survey and can settle questions that measurements alone cannot answer. It also protects you if a fit is disputed later. Under the Consumer Rights Act 2015 , a trader asked to repair or replace faulty goods has to do so within a reasonable time and without significant inconvenience to the customer, so a clear record of what was surveyed makes it much easier to agree what went wrong and put it right quickly.
Recording the order so nothing gets lost
A careful survey can still go wrong if the information does not reach the factory clearly. Use the same survey sheet layout for every job, so the people placing the order always know where to find each figure.
Alongside the sizes, record the style, the louvre size, the panel layout (how many panels, which way each one opens), the position of any mid rail and the frame type. Write down the colour or finish exactly as it appears in the supplier's range, rather than describing it in your own words. Small differences in wording are a common source of mix-ups.
It also helps to record what the customer asked for in plain language: privacy at street level, full blackout in a bedroom, easy access to a window handle. If a measurement and a request seem to conflict, that note gives the factory the context to flag it. The choices you make here, from louvre size to frame style, also affect the final price; the factors that affect the cost of made to measure shutters are worth understanding before you quote.
Period and listed properties
Older houses bring their own measuring challenges. Walls are rarely straight, sash windows have boxes and pulleys that need clearance and some properties still have original internal shutters hidden behind paint or panelling.
If you are surveying a listed building, ask the customer whether they have checked what consent is needed. Guidance from local authorities, such as Cotswold District Council's advice on windows in historic buildings , notes that reinstating original internal shutters may need Listed Building Consent. It is not your job to give planning advice, but raising the question early can save an awkward cancellation later.
Take extra diagonal measurements on period windows and photograph any original joinery. If the reveal is badly uneven, a face fit or a frame that can be scribed to the wall is often a better choice than forcing a reveal fit. If a job falls outside what you normally quote, speak to the trade team before confirming it with the customer.
Getting the survey right first time
Accurate made to measure shutters come from a consistent survey routine: decide the fitting method, take every measurement more than once, record every obstruction and write the order in the supplier's own terms. Each step takes a minute or two, and together they prevent most of the remakes that eat into margins.
British Made Shutters manufactures composite plantation shutters in Worcestershire for UK retailers and installers. If you would like a survey sheet template or advice on a tricky window before you order, get in touch with the trade team and ask about becoming a trade partner.
Frequently asked questions
Should I deduct anything from my reveal measurements?
That depends on the supplier. Some ask for exact recess sizes and make their own deductions for clearance, while others expect the surveyor to deduct. Always confirm the rule with your supplier and write "exact recess size" or "deductions made" on the survey sheet, so nobody deducts twice.
How deep does a recess need to be for a reveal fit?
The minimum depth depends on the frame type, louvre size and window handles. Larger louvres need more depth to tilt freely. Measure the clear depth from the face of the wall to the furthest projection on the window, usually the handle, and check it against the supplier's guidance for the louvre size the customer wants.
What is the best tool for measuring shutters?
A good steel tape is still essential, and a laser measure is useful for large openings and checking diagonals quickly. Whatever you use, measure in millimetres and avoid rounding. Rounding to the nearest centimetre is one of the simplest ways to end up with a frame that does not fit.
Can customers measure for made to measure shutters themselves?
Some online retailers allow it, but for trade businesses a professional survey is safer. A survey lets you spot obstructions, out-of-square openings and depth problems that customers rarely notice, and it means responsibility for the measurements sits with someone trained to take them.
Share this blog








